Auto-recharge keeps your wallet funded without manual intervention. When your balance crosses below the threshold you set, we charge a saved card and add the funds to your prepaid Top-Up Bucket.
Before you start
Section titled “Before you start”You need:
- At least one saved card. Add one from Payment methods before turning auto-recharge on.
Auto-recharge does not require a subscription: prepaid funds are spendable on their own. (If your wallet is frozen after a subscription cancellation, re-subscribe first; auto-recharge tops up a frozen wallet but the funds stay frozen until you re-subscribe.)
Turn on auto-recharge
Section titled “Turn on auto-recharge”Open Billing in the console. The auto-recharge form sits below the wallet summary. Toggle it on, set the threshold and recharge amount, pick the card to charge, and save.
Choose the threshold and amount
Section titled “Choose the threshold and amount”Two dollar amounts control the behavior. Enter both in whole dollars. The form does not accept cents, and the minimum is $1.
- Threshold: a recharge starts when your balance falls below this amount. A balance that is equal to the threshold does not start a recharge. Set the threshold high enough that a recharge lands before you run out.
- Recharge amount: how many US dollars to add each time. Auto-recharge funds 1:1 at the base rate; the preset checkout discounts are a manual-top-up lever only.
The threshold must be below the recharge amount, so that one recharge brings your balance back above the threshold. When the threshold is not below the recharge amount, the form shows an error on both fields and does not save. Lower the threshold or raise the recharge amount, then save again.
Set the threshold above the price of your most expensive check. When the threshold is lower than a check’s price, that check can be refused for low balance while your balance is still at or above the threshold. No recharge starts in that case, and the check does not run until your wallet has funds. See Payment required.
Pick a payment method
Section titled “Pick a payment method”Auto-recharge charges the card you select on the form automatically. Keep the card up to date: an expired or invalid card will fail the recharge and we’ll email you. Every declined or canceled recharge counts toward a failure limit. After five declined or canceled recharges in a row, auto-recharge turns itself off to limit declines on a problematic card. A decline that retrying cannot fix, such as an expired or lost card, turns it off at once. A successful recharge, or turning auto-recharge back on, starts the count again. Re-enable it once you’ve fixed the payment method.
How a recharge is triggered
Section titled “How a recharge is triggered”A recharge can start in five situations. Each time, we check your balance again before we charge your card. A recharge starts only when your balance is below the threshold and no other recharge is in progress.
- A debit takes your balance below the threshold. A debit is a charge against your wallet, for example when a check runs. The recharge starts soon after the debit.
- A check cannot start because your balance is too low. When your balance is below the threshold at that time, a recharge starts. The check does not run until your wallet has funds. See Payment required.
- You save the auto-recharge form while your balance is already below the threshold. The recharge starts soon after you save.
- You send a live-mode API request that we accept while your balance is below the threshold. The recharge runs in the background.
- The daily run happens. Once a day, we look for wallets that have auto-recharge turned on and a balance below the threshold.
When a recharge starts, the payment processor charges your card. On success, the funds land in your Top-Up Bucket as a grant_created transaction, exactly like a top-up, at the base rate (no discount). Your balance does not change until the payment is confirmed. Refresh the Billing page after a short time to see the new balance.
Auto-recharge runs without you, so your bank cannot ask you to approve a payment at that time. If your bank requires approval, the bank can decline the recharge. We then email you the decline notice with a link to Billing. On Billing, choose Add funds to make a manual top-up and approve the payment with your bank, or change the card. If an auto-recharge waits for your approval instead, we email you a Confirm the charge link to the Completing payment page in the console, where you finish it. See pending recharges.
When a recharge does not start
Section titled “When a recharge does not start”- Your balance is already below the threshold, and you do not spend or save the form again. The recharge waits for your next live-mode API request that we accept, or for the daily run.
- Your balance falls for a reason other than a debit. An expired grant and a refund of a top-up are examples. The recharge waits for your next live-mode API request that we accept, or for the daily run.
- Your balance is zero. When your balance is zero, we refuse API requests, so they do not start a recharge. Save the auto-recharge form, or add funds.
- A recharge is in progress, or one started or was declined or canceled in the last 5 minutes. Auto-recharge waits until the recharge in progress ends. It also waits until 5 minutes have passed since the last recharge started or the last decline or cancel. The next trigger after that can start a new recharge.
- Your last recharge was declined. See If a recharge is declined.
If a recharge is declined
Section titled “If a recharge is declined”When the card declines a recharge, we email you and count the decline. We try again in three ways, once 5 minutes have passed since the decline:
- You send a live-mode API request that we accept.
- The daily run happens.
- You save the auto-recharge form.
When your balance is zero, we refuse API requests, so they do not start a recharge. Save the auto-recharge form, or add funds. A debit does not retry a declined or canceled recharge. To retry soon after you fix the problem, add or update the card on Payment methods. Then pick the card on the auto-recharge form on Billing and save after the 5-minute wait. The save retries the recharge.
Pause or turn off auto-recharge
Section titled “Pause or turn off auto-recharge”Toggle auto-recharge off on the same form. Pending recharges already in flight will still complete. You can’t stop a single recharge that’s mid-flight: wait for it to finalize or fail, then disable the form.
Troubleshooting
Section titled “Troubleshooting”- Auto-recharge fired but funds didn’t land: see Pending recharges.
- Your balance is below the threshold and no recharge started: save the auto-recharge form again on Billing. A save starts a recharge when your balance is below the threshold. Wait 5 minutes first if a recharge started, was declined or was canceled a short time ago. When the form shows an error on the threshold, lower the threshold or raise the recharge amount, then save again. When a card was declined, update the card on Payment methods first.
- Auto-recharge turned itself off: a decline that retrying cannot fix, or five declined or canceled recharges in a row. Update the card on Payment methods and re-enable it.
- Auto-recharge shows “Disabled by you” after its card was removed: removing the auto-recharge card turns auto-recharge off. If the card was removed earlier, the next recharge attempt turns it off and we email you. Pick another saved card on the auto-recharge form and switch auto-recharge back on. See Remove a payment method.
- My card was charged twice: auto-recharge is deduped per balance dip; a true double-charge is rare. File a refund request and we’ll reconcile.